Home > All images > fluorescent > Control Gear

FILE 473/619

Thorn AME69046.4 65w SS Choke, Refurbished (now dead)

This was in a sad state when I acquired it, quite rusty and had been left outside for some time.

I completely stripped it back to mostly bare metal & painted it with zinc primer, then gave it a top coat of Plastikote Satin 'Porcelain'. Before I did this, I scanned the original etch, so I then printed it out and stuck it on. Finally it had two coats of satin lacquer.

How it used to look can be seen here

Also here

File information
Filename:	tmp_28262-IMG_20170720_1920561616297682.jpg
Album name:	fluorescent / Control Gear
Manufacturer:	Thorn
Type/Model:	AME69046.4
Wattage:	For 5ft 65w tubes
Date manufactured:	1970's
Filesize:	1317 KiB
Date added:	20 Jul, 2017
Dimensions:	2322 x 1383 pixels
Displayed:	74 times
URL:	http://80.229.24.59:9232/gallery/displayimage.php?pid=6508
Favourites:	Add to Favourites

Comment 1 to 15 of 15

Page: 1

Simon_R

[20 Jul, 2017 at 11:09 PM]

Nice job...That looks great Smile

Slyspark

[21 Jul, 2017 at 01:25 AM]

Looking good!

fluorescent

[21 Jul, 2017 at 01:31 AM]

Thanks folks

fluorescent

[22 Jul, 2017 at 09:28 AM]

...hmm think I should have used heat resistant paint Sad

Danny

[22 Jul, 2017 at 01:45 PM]

Looks really nice

fluorescent

[22 Jul, 2017 at 01:45 PM]

Update: It's now hard down to earth! Oh well in the bin it goes. Was great practice for next time Rolling Eyes

Slyspark

[22 Jul, 2017 at 03:58 PM]

Radiator enamel is what I use on mine. Shame it's fucked Sad

fluorescent

[22 Jul, 2017 at 05:05 PM]

Radiator enamel is a good idea as chokes probably run at similar temperatures? I had this running 24/7 for 3 days & it tested completely clear of earth before I painted it! Oh well...

Slyspark

[22 Jul, 2017 at 07:16 PM]

Just a thought - you've not gone and got zinc primer in any of the terminals or in the 2 small holes in the backplate have you as that would certainly conduct! I make a point of using only non-conductive paint on ballast restorations - just in case!

Kev

[22 Jul, 2017 at 07:28 PM]

Ay?? These are amazing ballasts wonder why that's happened

fluorescent

[23 Jul, 2017 at 08:53 AM]

The terminals were covered as was the small hole on the back. I wouldn't of thought any zinc primer got in & even if it did aren't these filled? I dunno I'll see if I can investigate further...

Slyspark

[23 Jul, 2017 at 11:20 AM]

Not uncommon for the polyester resin to crack over time, so it's always possible. Unlikely I know, but still theoretically possible. If you covered the terminals and the hole then no idea, you've probably just got unluckily Sad

lampy

[24 Sep, 2018 at 08:31 PM]

had quiet a few of the rounded corner SRS thorn ballasts burn out on me, all looked fine when i got them but after some light use they failed, mind all had been derelict building salvages, so maybe damp gets in them over time

Slyspark

[24 Sep, 2018 at 08:49 PM]

I'll second that, also had some of the SRS ballasts in that type of can fail. Also rescues from derelict buildings. The later, open-canned ones seem to fair better!

fluorescent

[24 Sep, 2018 at 09:37 PM]

How did yours fail Lampy, earth leakage? I've still got this knocking about somewhere, I will cut it open one day to see what happened, although I'd bet all the filling has shrunk/cracked as Rich suggested and it'll be corroded inside

Comment 1 to 15 of 15

Page: 1